Atop-technology EH7510 User manual Manuel d'utilisateur télécharger pdf (Page 30)

Atop Industrial Managed Ethernet Switch

EH7510

User Manual V 1.0

2.3.8 PTP Setting

The Precision Time Protocol (PTP) is a high-precision time protocol. It is for precise

synchronization of clocks on a local area network by measurement and control systems. Fig.

2.20 (on the next page), shows where to configure PTP and to see PTP status

Fig. 2.20

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 119 120

User Manual 1
Important Announcement 2
Published by 2
Atop Technologies, Inc 2
Table of Contents 3
Preface 7
Chapter 1: Introduction 8
Caution 10
1.4 Power Requirements 11
1.6 LED Indicators 11
2.2.2 Console 15
2.2.3 Power Status 15
2.2.4 Protocol Status 16
2.3.2 Password 18
2.3.3 IP Settings 19
2.3.4 Forwarding and QoS 20
2.3.4.1 CoS Mapping 23
2.3.4.2 ToS/DiffServ Mapping 24
2.3.5 Mirror Port 25
2.3.6 System Time and SNTP 26
2.3.7 Modbus Setting 27
2.3.8 PTP Setting 30
2.4 Port 32
2.4.1 Port Status 32
2.4.2 Port Statistics 33
2.4.3 Port Control 34
2.5 Trunking 35
2.5.1 LACP 35
2.5.2 Trunking 36
2.6 Unicast/Multicast MAC 37
Multicast 37
Unicast 37
2.6.1 MAC Address Table 38
2.6.2 Add Uni/Multicast MAC 38
2.6.3 Filter MAC 39
2.7.2 GARP 41
2.7.3 GVRP 42
2.7.4 GMRP 43
2.8 IGMP/IP Multicast 44
2.8.2 Static IP Multicast 45
＊Example＊ 46
2.8.3 IGMP 47
2.8.4 IGMP Statistics 48
2.9 SNMP 49
2.9.1 Community Strings 50
2.9.2 Trap Receivers 51
2.9.3 SNMPv3 Users 51
2.10 Spanning Tree 52
2.10.1 Spanning Tree 53
2.10.2 Spanning Tree Port 55
2.11 VLAN 56
2.11.1 VLAN Mode 58
2.11.3 VLAN Setting 61
2.12.2 Add Static MAC 67
2.12.3 802.1x and Radius 68
2.12.4 802.1.x 69
2.12.5 802.1x Port 70
2.13 ERPS/Ring 71
2.13.1 DIP Switch 71
2.13.2 ERPS 73
2.13.3 iA-Ring 79
2.13.4 Compatible-Ring 81
2.13.5 U-Ring 82
2.14 LLDP 84
2.14.1 LLDP 84
2.14.2 Neighbors 85
2.15 System Warning 86
2.15.2 Alert Warning Events 88
2.15.3 SMTP Settings 89
2.16 Diagnosis 90
2.17 System Log 92
2.17.1 Syslog 92
2.17.2 Event Log 93
2.18 System 95
2.18.1 Backup/Restore 95
2.18.3 TFTP 97
2.18.5 Reboot 99
3.1 Serial Console Setup 100
3.3 General Command 103
3.4 Command Example 103
4.1 SwitchView 106
4.2 Firmware Upgrade 107
4.3 Topology Diagram 108
System Information 109
Console Information 110
Power Information 110
IP Information 110
System Status Clear 111
Warning Events Information 111
Port Status 111
Redundancy Information 115
Glossary 119

Commentaires sur ces manuels

Pas de commentaire

Atop-technology EH7510 User manual Manuel d'utilisateur Page 30

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel informatique Atop-technology EH7510 User manual